This list is divided into four sections: 1.
Shelby American Production Changes 2. G.T.350 Production Changes 3.
G.T.500 Production Changes 4. FoMoCo Production Changes
1.0 Shelby American Production Changes
1.1.
Headlights Inboard Outboard
1.2. Body Assembly, Front (Nose) One Piece w/fiberglass cloth
backing Two Piece w/fiberglass cloth backing One Piece w/chop gun
fiberglass backing
1.3. Grilles One-piece, slanted, inboard headlights Two-piece,
slanted upper, straight lower, inboard headlights Two-piece, straight,
inboard headlights Two-piece, straight, outboard headlights
1.4. Headlight Trim Bezels Body color Chrome
1.5. Headlight Buckets Early style held with clamps Late
style bolted to plate
1.6. Grille Emblem Not installed Installed
1.7. Air Extractor (Upper Scoops) Lights Not installed
Installed
1.8. Hood Pin Lanyards Attached to grille Attached to hood pin
bracket
1.9. Brake Scoops Functional (center duct) Functional (lower
duct) Non-functional
1.10. Tail Light Bezels Studded Through Hole
1.11. Rear Tail Light Panel Flat Curved (or Raised)
1.12a. Gas Cap Flat Convex (Curved)
1.12b. Gas Cap FoMoCo marked Autolite marked
1.13. Front, Rear, and Side Emblems Flat Embossed
1.14. Exhaust Trim M/F GT Mustang M/F Cougar No trim
1.15. Roll Bar Six-point Six-point w/cutoff legs
Four-point
1.16. Inner Quarter Panel Rollbar Rubber Trim (Donuts) Not
installed Installed
1.17. Roll Bar Cover Removable Molded
1.18. Fold-down Seat Latch Trim Plates Not installed
Installed
1.19. Hoods Steel frame All fiberglass
1.20. Deck Lids Steel frame w/trunk lamp Steel frame w/o trunk
lamp All fiberglass
1.21. Amp Meter Junction Block Gray Black
1.22. Amp Meter Wiring Spiral wrap Vinyl tube Tape
1.23. Tail Light Wiring Harness Cover Loose wire Tape
wrapped Enclosed plastic sheath (vinyl tubing)
1.24. Optional Wheels KH MagStar SAI 10-Spoke
1.25. Tires Large lettered "GOODYEAR" Small Lettered
"GOODYEAR"
1.26. Sill Plate 1966 Style One Line Shelby American (Shelby
American Inc.) Two Line Shelby American (Shelby American Inc., Los Angeles
California)
1.27. Gauge Pod Center Plate w/o mounting screws w/ mounting
screws
1.28. Underdash Seat Belt Warning Light Installed Not
installed
1.29. Steering Wheel w/ short tabs w/ long tabs
1.30. Exhaust Tips Two piece (welded) One piece
1.31. SAI VIN hand lettered stamped w/o "Z" stamped w/
"Z"
2.0 G.T.350 Production Changes
2.1. Intake Manifold S2MS 9424-A S7MS 9424-A
2.2. Distributor FoMoCo marked AUTOLITE marked
2.3. Fan Shroud FoMoCo in rectangle marked FoMoCo in oval
marked
3.0 G.T.500 Production Changes
3.1. Air Cleaner Sandcast, non COBRA lettered Diecast, COBRA lettered,
black painted finish Diecast, COBRA lettered, natural finish
3.2. PVC Connection to intake manifold To air cleaner
4.0 Ford Production Changes
4.1.
Upholstery Standard (Smooth) Comfort Weave (Deluxe)
4.2. Fuel Line Routed along rocker panels Down drive shaft
tunnel
4.3. Windshield Washer Bag reservoir Bottle reservoir
4.4. Oil Filler & Breather Caps Black painted "FoMoCo"
stamped "AUTOLITE" stamped
4.5. Standard Steel Wheels 15 X 6.5 15 X 6
4.6. Rear valence Standard - no exhaust cut outs GT with
exhaust cutouts
4.7. Battery Hold Down w/extra bracket w/o extra bracket
4.8. Steering Column w/o "rag joint" w/ "rag joint"
4.9. Door Panel Trim (Brushed Aluminum) flat forward edge
curved forward edge
4.10. Fold-down Seat Latch w/o latch cover plate w/ latch cover
plate
4.11. Front Seat Trim Attached w/ two screws Attached w/ three
screws
4.12. Battery Apron Reinforcement Narrow Wide
4.13. Horn Date Code Ink stamped Metal stamped
4.14. Rear End Housing W/fill plug in back of housing W/O fill
plug
4.15.